|
S-ton
Mar 25, 2013 23:34:55 GMT -5
Post by chevtech on Mar 25, 2013 23:34:55 GMT -5
Eliminating all the unnecessary wiring/connectors from the harness, making it a 3 wire hookup to run the engine. Pcm is getting programmed to eliminate the transmission, down stream o2 sensors and other unnecessary stuff. Pcm is then getting timing and fuel tuned for more power!
Front end is getting a tube core support and all new tubing tying the cage to the core support.
|
|
|
S-ton
Mar 26, 2013 10:26:54 GMT -5
Post by 2manytoys on Mar 26, 2013 10:26:54 GMT -5
Where did you have to send your harness, & PCM to? How much xtra HP from the PCM?
|
|
|
S-ton
Mar 26, 2013 22:34:22 GMT -5
Post by chevtech on Mar 26, 2013 22:34:22 GMT -5
I sent it to a guy in Reno, tune is good for 20+ hp and 30-40 ft/lbs of torque, he also gets rid of all the torque management and changes the fuel enrichment so it starts making good power right off idle. Should be 350+ hp and 400+ ft/lbs of torque. I also sent him my throttle pedal and throttle body for him to calibrate since my engine is drive by wire.
|
|
|
S-ton
Mar 31, 2013 0:20:35 GMT -5
Post by chevtech on Mar 31, 2013 0:20:35 GMT -5
|
|
|
S-ton
Mar 31, 2013 1:14:13 GMT -5
Post by CRAZY BASTARD on Mar 31, 2013 1:14:13 GMT -5
That looks awesome Josh
|
|
|
S-ton
Apr 1, 2013 9:46:31 GMT -5
Post by 2manytoys on Apr 1, 2013 9:46:31 GMT -5
That is turning out really good, are you going to be able to narrow the grille, or will you have to fab one?
|
|
|
S-ton
Apr 2, 2013 0:57:05 GMT -5
Post by chevtech on Apr 2, 2013 0:57:05 GMT -5
Got the engine harness/pcm/throttle pedal/throttle body back from getting modded, hooked it up and test fired it, it's ALIVE!!! Click on image for video.
|
|
|
S-ton
Apr 2, 2013 14:42:58 GMT -5
Post by 2manytoys on Apr 2, 2013 14:42:58 GMT -5
That sounds really good!! Nice & smooth.
|
|
|
S-ton
Apr 6, 2013 23:40:15 GMT -5
Post by chevtech on Apr 6, 2013 23:40:15 GMT -5
Radiator mounted Pcm and fuse panel mounted Also got it wired to the truck and fired it off the key! Just have a few more things to do on the motor and it will be finished. I have more to do on the rig before its ready to wheel, but shooting for a memorial day run.
|
|
|
S-ton
Apr 14, 2013 19:29:08 GMT -5
Post by chevtech on Apr 14, 2013 19:29:08 GMT -5
|
|
|
S-ton
Apr 15, 2013 9:26:46 GMT -5
Post by 2manytoys on Apr 15, 2013 9:26:46 GMT -5
That turned out good, I like the grille.
|
|
|
S-ton
Apr 15, 2013 9:32:14 GMT -5
Post by CRAZY BASTARD on Apr 15, 2013 9:32:14 GMT -5
Looks awesome josh
|
|
|
S-ton
Apr 16, 2013 10:08:15 GMT -5
Post by shaggy on Apr 16, 2013 10:08:15 GMT -5
That looks sweet.
|
|
|
S-ton
Apr 21, 2013 20:59:22 GMT -5
Post by chevtech on Apr 21, 2013 20:59:22 GMT -5
|
|
|
S-ton
Apr 22, 2013 9:54:58 GMT -5
Post by 2manytoys on Apr 22, 2013 9:54:58 GMT -5
I like the slider for the rear mount, should give you plenty of droop. I was thinking the same when I put the 60 under the cruiser. Looks like it should work out OK.
|
|